When removing a towel bar with a slot, you need to be careful about which way you remove it. If the slot is facing down, then you’ll have to keep the towel bar intact and find another way of removing it from above. If the slot is facing up, however, removing the towel bar will be much simpler. Remove the screws that secure the towel bar to the wall and carefully pull out the remaining piece of this fixture. Afterward, sand down any rough edges and paint over them if you’re not happy with their new look. Check out these tips on how to remove a towel bar with a slot!
How To Remove Towel Bar With Slot?
Pull It Out By The Slots
The most obvious way to remove a towel bar is to simply pull it out by the slots, but this isn’t always the best option. In some cases, the towel bar is mounted to the wall with screws that go directly through the slots. This means you’ll have to remove the screws first if you want to pull the towel bar out. Other times, the towel bar is mounted with a lock nut or some kind of mounting clip. In these cases, you may be able to pull the towel bar out by the slots, but you’ll also have to remove the mounting clip or lock nut before you can finish removing the towel bar. In each of these cases, you’ll have to do some extra work to remove the towel bar. You’ll have to figure out where the towel bar is mounted, find the appropriate tools, and then remove the mounting screws or clips.
Use A Saw To Trim The Metal
If the towel bar is mounted with a lock nut or mounting clip and you can’t get it out by the slots, you should consider using a saw to trim the metal. First, you’ll want to determine where the towel bar is mounted. You can do this by feeling for the mounting screws with your hands or by using a mounting stud finder. Once you’ve found the location of the mounting screws, use a screwdriver or a saw (depending on their type) to remove them. Once you’ve removed the screws, pull the towel bar out by the slots, but don’t remove the entire towel bar. Instead, use the saw to cut the excess portion of the metal where the mounting clip or lock nut is located. This should be enough to remove the towel bar.
Cut The Pipe And Discard It
If the towel bar is mounted with a lock nut or mounting clip and you can’t get it out by the slots or with a saw, you can consider cutting the pipe and discarding it. The first thing you’ll want to do is to determine where the towel bar is mounted. Once you’ve found the location, use a wrench to remove the mounting nuts or screws. Next, use a hacksaw to cut the pipe just below where the towel bar is mounted. If you cut the pipe too low, you won’t be able to attach the new towel bar. Once you’ve cut the pipe, the towel bar should fall off by itself. You’ll then want to clean up the cut end of the pipe, make sure it’s smooth, and reattach the new towel bar.
Ditch The Towel Bar Altogether
Instead of cutting the pipe and discarding it or removing a towel bar by the slots, you can also consider just removing the entire towel bar altogether. To do this, you’ll have to find the location of the mounting screws or clip, then use a screwdriver or wrench to remove them. Once the towel bar is loose, you can just lift it off the wall. You may want to use pliers to get a better grip or pull the towel bar out by the slots before you lift it off the wall. Once the towel bar is off the wall, you can just set it aside until you’ve found a replacement. You can also temporarily mount another type of towel rack in its place until you’ve found a new towel bar.
Saw With A Rotating Blade
If the towel bar is mounted with a lock nut or mounting clip and you can’t get it out by the slots or by cutting the pipe and discarding it, you can use a rotating saw to remove the towel bar. This is essentially like using a saw to cut the pipe and discarding it, except you’ll want to make sure to cut the pipe higher up the wall. You’ll also want to use a saw with a rotating blade so that you can get the towel bar out in one clean cut. If you have the saw on the lowest setting, you might have to make multiple cuts in order to get the towel bar out. Once you’ve cut the towel bar, it should fall off the wall by itself. You’ll then want to clean up the cut end of the wall and reattach a new towel bar.
How To Remove A Towel Bar With A Slot From Below?
- If the towel bar has a slot facing below, then you’ll need to find another way of removing it from above because the pry bar will only dig a deeper slot into the wall.
- One option is to use a chisel and hammer. You’ll want to place the chisel where the slot is and firmly hit it with the hammer.
- This will create a small crack in the wall, but don’t worry! You can use spackling putty to fill in the crack and make the wall smooth again.
- You can also use a drill and a spade bit. You’ll want to place the towel bar on the drill and drill a small hole below the towel bar.
- Next, you’ll want to place the spade bit in the drill and drill through the towel bar.
- This will make removing the towel bar much easier because you can just unscrew it from below.
How To Install A Towel Bar With A Slot?
- Installing a towel bar with a slot is actually a pretty easy task! You’ll want to start by
- measuring the wall where you want to install the towel bar.
- Once you know where the towel bar should be, you’ll want to mark the spot with a pencil.
- Next, make a mark where the slot on the towel bar should go in the wall.
- Next, you’ll want to use a drill to make a small pilot hole where your mark was made on the wall.
- After that, you’ll want to use a screwdriver to screw the towel bar into the wall. You’ll want to make sure that you’ve screwed it in tightly so that it doesn’t fall off.
Tips For How To Remove A Towel Bar With A Slot?
Ask A Friend For Help
If you’re trying to remove a towel bar with a slot, it’s most likely installed on drywall. This means that you’ll need to take out the drywall anchor that is holding it in place in order to remove it. However, this can be a difficult process and you might not have the strength needed to finish the job. If you’re unsure of your own abilities, it might be a good idea to ask a friend to help. If you have a couple of strong friends, there are a few ways to remove the towel bar. You can have one person hold the towel bar in place while the other person uses a drill to take out the anchor that is holding it up. Or you can have one person hold the towel bar in place while the other person uses a hammer and chisel to break out the drywall.
Use A Sawing Tool
There are a couple of different sawing tools that you can use to cut out the drywall anchor from behind the towel bar. The Sawzall is one of the more popular sawing tools that people use for this job. It looks a little bit like a reciprocating saw but with a large rotating blade instead of a small saw blade. The other sawing tool is the Electric Sawzall. This tool has a rotating blade just like a regular Sawzall, but it’s powered by electricity. These tools can be fairly easy to use and will definitely get the job done. However, you do need to make sure that you’re wearing eye protection in case the blade of the saw comes loose and flies toward your face. You also need to make sure that you’re wearing gloves so you don’t get your hands cut on the rotating blade of the saw.
Use An Impact Driver Or Hammer Drill
If you’re not comfortable using a sawing tool to remove the anchor, you can always use an impact driver or hammer drill. The best impact driver to use for this type of project is the cordless type. This will allow you to maneuver around the towel bar without being tied down by a long cord. A hammer drill is also a great tool for removing drywall anchors because it has a special bit designed for breaking down drywall. The main difference between the two tools is that the hammer drill rotates in a clockwise direction while the impact driver rotates in a counterclockwise direction. Keep this in mind when deciding which tool to use.
Summary
If the towel bar has a slot facing down, you’ll have to be careful about removing it from above so that you don’t damage the wall. If the slot is facing up, however, removing the towel bar will be much simpler. If the towel bar doesn’t have a slot, then you’ll just need to unscrew it from the wall. If the towel bar has a slot, then you’ll need to use a different method to remove it depending on whether the slot is facing down or facing up. Installing a towel bar with a slot is actually a pretty easy task! You just need to make sure that you are using the correct size drill bit.
